Bài này sưu tầm, anh em nào có máy thì thử: ........................... These are instructions on how to dump the SHSH blobs of your current firmware even if Apple is not signing For instance, you can dump the SHSH of the current firmware on your device, so long as the device is susceptible to the Limera1n jailbreak (Everything but the iPad 2) Apple does not have to be signing the SHSH in order for you to dump the blob. *Note:The iPod Touch 2G and iPhone 3G will not work since they will always be jailbreakable. The iPad 2 will not work because it is not susceptible to Limera1n. A jailbreak is not needed for this. Step One Download the iFaith from<Bạn vui lòng đăng nhập hoặc đăng ký để xem được nội dung này!> Step Two Extract the downloaded zip file, and double click the iFaith.exe file. Step Three A disclaimer will appear. Read the notice and click ok to proceed. Step Four Click the Dump SHSH Blobs button. Step Five Read the information and click Proceed when you are ready. Finally, click the Let's Go! button to start the dumping process. Step Six If you are dumping an Apple TV 2, indicate it when iFaith asks you Step Seven Follow the DFU Instructions to place your device in DFU Mode. <Bạn vui lòng đăng nhập hoặc đăng ký để xem được nội dung này!> <Bạn vui lòng đăng nhập hoặc đăng ký để xem được nội dung này!> Press Power and home for 10 Seconds Release the power button, but keep holding the Home Once Successful, iFaith will dump the SHSH of your current firmware. It will go through each step which could take a few minutes. <Bạn vui lòng đăng nhập hoặc đăng ký để xem được nội dung này!> <Bạn vui lòng đăng nhập hoặc đăng ký để xem được nội dung này!> Step Eight When completed, iFaith will ask you where to locally save the SHSH. Indicate where you want to save the SHSH file. Step Nine iFaith will notify you that the process was successful A video Guide............! **Thanks goes to iH8sn0w and everyone else who helped in making this tool [QUOTE iFaith v1.3 - Release Notes (read it all!) ~Important~ * DFU Loops were being caused on devices that had the factory certificate. On this new version. When building the signed IPSW. If you were getting a DFU loop, say "NO" to the prompt about using the standard signing certificate. ------------------------------- * You can now use TinyUmbrella blobs to build a signed IPSW. [Change Filetype in browse dialog to "TinyUmbrella SHSH blobs".] ------------------------------- * Now adds ECID to beginning of the SHSH filename after dumping. * Now adds ECID to beginning of the IPSW filename after being built. * Cleaned up code + payload. * Its not possible to add iPad 2 support until a bootrom exploit arises. ------------------------------- Many Thanks to @sbingner & @Sk0ODaT ][/QUOTE] iFaith v1.3.2 - Release Notes For iOS 3.1.x/3.2.x/4.0.x/4.1/4.2.1/4.2.6/4.2.7/4.2.8/4.3/4.3.1/4.3.2/4.3.3 Changelogs The .NET framework that came pre-shipped with Windows Vista didn't have an essential resource used in iFaith. A new method has been implemented to get around this requirement. Fixed issue where iTunes' plist utility was unable to be located on international language formatted pcs. It supports the following devices iPhone 3G iPhone 4 iPod Touch 3G iPod Touch 4 iPad 1G Apple TV 2 ALTERNATIVE LINKS OF IFAITH <Bạn vui lòng đăng nhập hoặc đăng ký để xem được nội dung này!> <Bạn vui lòng đăng nhập hoặc đăng ký để xem được nội dung này!> <Bạn vui lòng đăng nhập hoặc đăng ký để xem được nội dung này!> NOTE:This Software Is Still Buggy TRY AT YOUR OWN RISK The Old Sticky can be Found Here: <Bạn vui lòng đăng nhập hoặc đăng ký để xem được nội dung này!>
